Home > Fuser Error > Fuser Error 50.8

Fuser Error 50.8

Then reinsert the power supply and power the AIO on.Did the error message return? If so, replace the fuser. 6.If error returns, then replace DC controller and upgrade the firmware HP RM1-2580-000CN DC Controller Assembly-clj 3000-r1.55.00 MFG Part Number: RM1-2580-000CN Condition:Refurbished MFG:HP Traditional fusers have two rollers: a heated roller which is a hollow metal cylinder coated in teflon with a halogen lamp down the middle. You may NOT copy or distribute the content that appears on this site without written permission from Fixya Ltd. © 2005-2015, Fixya, Ltd. weblink

Make sure that the connector J1002  and J1505 are fully seated on the ECU. The email address entered is already associated to an account.Login to post Please use English characters only. Replace the connector as necessary.3. A single thermistor can represent the temperature across the whole upper roller.

It is surprisingly robust as well, Teflon-like materials adhere to one another better than they adhere to aluminium so there is no definite sacrifice in longevity. Did the error message return? Service companies love to mark up parts and charge steep repair rates to handle this simple replacement. Replace the connector as necessary. 3.

Jun 09, 2014 | HP LaserJet 3600n Printer 0 Answers COLD RESET HP 3600N COLD RESET Jun 06, 2014 | HP LaserJet 3600n Printer 0 Answers PCL XL error Subsystem: KERNEL In this article I'll discuss a few of the tips that can help you troubleshoot   the error condition, give you input on what the service manual has to say in HP do themselves no favours. fortwayneprinterrepair I like this site but this is just the index page and not an answer to the query.

Thank you. Turn on the power and wait for the all-inone to initialize.5. I had a cracked scanner glass which I replaced. Remove the color cartridge and insert the black/photo cartridge.

If that doesn't fix it then you will have to replace the fuser. Solution: 1. If I power it off and instantly power it back on it will print, just as before, but if it sits very long it will give a fuser error when you I have updated the firmware as well and this didn't change anything.

If the error message reappears, replace the black print cartridge with a new print cartridge.If it does not repeat steps 1-3 and then go to step 7. Replace the DC controller PCA. Using the carrier belt, move the cartridge carrier to the middle of the unit. Turn off the printer.4.

thanks Might be NTC6, which is located in ... 05 is appearing on the. It takes a lot of time and effort to put these articles together. Check Out the Latest Printers Report View all Fixya Reports Top HP Printers & Copiers Experts kakima Level 3 Expert 96050 Answers k24674 Level 3 Expert 7983 Answers Brian Sullivan Level This is both a penalty but potentially an advantage of using a fuser sleeve.

I tried updating the firmware but that did not help either, it was just a shot in the dark. It appears that if the margin is too cool it will give "50.8" but more likely it will overheat and give "50.9". Yes: Repeat step 4 with another black/photo cartridge. check over here Also it allows the fuser and other components to cool down so when the machine restarts it has a better chance of getting to the correct operating temperature.

We do not sell these spare parts.We help you to create your parts sheets to request from your suppliers. Please enter a valid email address. or its affiliates.

Yes: Continue to Contacting Lexmark.No: Continue to step 3.3Power off the AIO and remove the power supply from the back of theunit.

Using the carrier belt, move thecartridge carrier to the middle of the unit. Now they are getting more specific in detail so you can troubleshoot errors like the 50.8 fuser error, making them easier and hopefully resolving the issue without buying unwanted parts.   If the resistance is not 100 kohms to 3 Mohms, replace the fuser.6. Did the error message return?

A particular focus of mechanical and thermal stress at the margins creates "edgewear". It now gives a fuser error immediately on trying to print , but if you power down and right back up, it will print succesfully. The P4014 series use a thin fuser sleeve as a medium to heat the paper. this content Power cycle the product to determine if the error is persistent. 2.

There could be a potential issue with control. Second thing to take a look at is the power source. Open the top cover of the AIO. The steps below will help you to resolve the issue and clear the error message.Printer Reset NOTE: The embedded links in the table lead to specific troubleshooting documents.StepAction1Power off the All-In-One