laptopcomputerszone.com

Home > Fuser Error > Fuser Error 50.3

Fuser Error 50.3

HP 4200 Laserjet 50.3 Fuser Error High Temp. Always Remove Power from the printer before working on it! I've personally had to adjust the printer temp on some machines to correct issues with certain types of media. Am I getting the error because of the paper jam? weblink

If the heat outside the machine is too high again it doesn't allow for correct cooling of the machine resulting in the 50.3 fuser error.Conclusion about The HP 4240, 4250, 4350 Maxwell [email protected] Posted on May 28, 2008 Helpful 4 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video Images Hashem Nashash Level 2: Turn the printer off for at least 10 minutes, then turn it back on. The gears should rotate smoothly. http://printerrepairsupport.com/50-3-fuser-error-hp-p4015-p4015-p4515/

Aug 11, 2009 | HP Color LaserJet 2600n Printer 1 Answer HP Laserjet 5m, appear error code 50...please help. Lamps can break in shipping or if the fuser is dropped. The high voltage power supply HVPS main purpose is to charge the toner cartridge with a much higher dc voltage.

Open the 2000-sheet input tray transfer door (if installed), tray 1, and the right lower door assembly 4. Remove 7 screws Note: Make sure you remove the LVPS fan from the unit and put it on the new one before installing back in your machine. Also, on my Mac the printer has an error message "OPC at end-of-life." Apr 23, 2014 | HP LaserJet 4350 Printer 0 Answers 4350 last sheet jam Apr 17, 2014 | If you still have the 50 Service error after reseating the fuser, you might need a new fuser.

Power supply is the most common cause. (RG5-4357) Pull the fuser out and check the thermal fuse on top of the fuser and the lamps inside the unit for continuity to If you don't wait 15 minutes you will continue to get this error even if you have replaced the fuser. a lot of 3rd party vendors ship the wrong fuser out. Jun 25, 2008 | HP LaserJet 4mv Printer 2 Answers Hp 2605n Fuser error 50.7 50.7 means that the photo sensor ps6 detected no movementOpen the side of the printer power

Any advise will be appreciated. All rights reserved. This allows the capacitor that is responsible for signaling this error to discharge. Thanks again, for all the support.

Respond to this 1 If you want to save a few bucks, I can supply you with just the heater portion of the fuser and an instructional video to replace it. https://mindmachine.co.uk/products/HP_Texts/HP_LJ-P4010_-_ops_error-50.3_01.html If this does not clear the error, replace the fuser. Pull the fuser straight back and out of the printer.Hopefully, this article has helped you troubleshoot the 50.3 fuser error in your HP laserjet 4240, 4250, and 4350. Try replacing the fuser unit.

best of luck. http://laptopcomputerszone.com/fuser-error/fuser-error-50-8.html eCommerce Solution : k-eCommerce Search Fixya Press enter to search. All Rights Reserved. Step 2: Please assign your manual to a product: About Advertising About Us Blog Careers News & Media Help Contact FAQ Partners Privacy Policy Terms Community Forums Recent Q&A Top Experts

by Stephen on Mar 14, 2007 at 6:35am Add comment Please sign in to comment 0 Thanks for the information. Check the continuity between connectors J1307-1 (callout 1) and J1307-2 (callout 2). The email address entered is already associated to an account.Login to post Please use English characters only. check over here Find maintenence kitInstallation instructions Home Page Technical Resources Lexmark Error Codes HP Error Codes Tech Support Blog HP Drivers Lexmark Drivers Terms & Conditions Product Conditions Definitions Web Order

or it's affiliates. Remove 3 screws Back Cover Note: Remove the metal back cover and the plastic panel at the right side rear cover as a single unit. Fan 3, Formatter Fan Fan Housing 1.

Action Turn the printer off.

Condition Posted by Kevin Gumpp at 12:05 am Tagged with: 4240, 4250, 4350, 50.3, error, fix, fuser, fusing assembly, HP, laserjet, repair, RM1-0182, serviceLeave a Reply Cancel reply Your CommentYou may Make sure that the Fusing Assembly is installed correctly and is fully seated into its connectors (no bent pins or pins outside their receptacles). 2. Corporal: An expert that hasĀ over 10 points. The fuser is running too hot, order rebuilt.*** Notes to remember!!

You can get one on Ebay for less than $50. Are you no longer selling??? - greybeards 0 50.3 has nothing top do with jams.DO not use "spray stuff" on the rollers.For black rubber rollers use:http://www.fixyourownprinter.com/specials/misc/chemicals/S03For gray rubber rollers take the or its affiliates. this content With the menu map you can look through the menu structure of the machine and work your way through the fuser settings.

What is a fuser? Governor: An expert whose answer gotĀ voted for 20 times. Or just drag it here! Check continuity between connectors J1308-3 (callout 3) and J1308-1 (callout 4) with the fuser removed.

Fuser Error Code 50.1: Low fuser temperature 50.2: Fuser warm-up service 50.3: High fuser temperature 50.4: Faulty fuser 50.5: Inconsistent fuser (verify voltage model) Service Manual Recommended Action Turn the printer by Stephen on Mar 14, 2007 at 3:35pm Add comment Please sign in to comment 0 I have seen that 50.3 error a couple of times where it actually picks up We sold the website and the new owner is just maintaining the forum. remove the fuser, check the white label, and make sure the part number reads RM1-1082 xxx.

If the printer fails to initialize when turned and displays "warming up" or if it just jumps to 50.1 error, those are indications that you have a power supply problem. thus allowing the fusing unit inside the printer to cool off. Check the pressure roller and gears for signs of wear. Contributor 1 Answer Re: hp 4350 error code 50.3 I have just changed the fuser unit and the printer is still giving the same error [fuser error and low heating] Kindly