Home > Error Code > What Does F10 Mean On A Frigidaire Oven

What Does F10 Mean On A Frigidaire Oven


You can find it on the range frame behind the bottom drawer. Control may have shorted relay, RTD sensor probe may be bad. It does indeed appear to be the Temperature Probe as the plastic wire harness connector is melted. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. his comment is here

If there is no continuity, the heating element is the culprit. Please check back in a few minutes. This part is usually located on the back wall in the upper part of the oven cavity but it can be easy tested from the EOC. I am lost as to how to proceed next as the touchpad was included with the new EOC?

What Does F10 Mean On A Frigidaire Oven

Is there anything internal to the oven where we could turn off the appliance?esequiel walker :No just unplug it. In this model the keypad is a part of the EOC. Gene.

The part number for the EOC (aka a clock/timer) is 316418735 Good luck. When I replace the EOC again do you think I need to be concerned with the Molex connectors for the temp probes on both ovens? I disconnected the stove and plugged it back in, the broil and oven elements still do not work and they visibly appear fine. Frigidaire Gas Range F11 Error Code Your stove is new and suppose to be covered under manufacturer warranty.

A code never flashed on the screen. Frigidaire Oven F10 Beeping If you have any questions please feel free to comment. I was able to clear the lock and the oven gave an F1 code. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden?

The part number for the EOC is 316418735 Good luck. Frigidaire Rtd Sensor The part number for the EOC is 316462800. Thank you in advance! I had noticed the same thing earlier in the day while baking chicken but no code came up at that time.

Frigidaire Oven F10 Beeping

Rachel // Mar 14, 2015 at 8:14 am Hello, My range is showing F10 error code since this morning. If open, replace Lock Motor Assembly. 5. (F90, 91, 92, 93 & 94) Lock Motor continuously runs - if Micro Switch is open, replace Lock Motor Assembly. 6. (F92, 93 & What Does F10 Mean On A Frigidaire Oven I will show you how to diagnose and fix them depending on the fault code. Frigidaire Oven F10 Reset They ship overnightJACUSTOMER-nuon2qee- :Where is the breaker located and the plug?esequiel walker :The breaker is normally outside the house on the mains.

The normal reading should be about 1100 Ohms at room temperature. this content Check Sensor wiring harness between EOC & Sensor Probe connector. 2. (F30 or F31) Check resistance at room temperature, if less than 500 ohms, replace **RTD Sensor Probe. Richard // Mar 10, 2015 at 6:08 pm Gene, you mentioned "day time mode" under your error code p10 description. See Details More Products Kenmore Installation Hose for Gas Range See Details Maytag Burner Switch 7403P181-60 See Details Range Kleen Replacement Drip Pan 2 pack - ... Frigidaire Eoc

If fault returns when power is reconnected, continue the troubleshooting. If the reading at the sensor is the same as reading at the EOC plug, the sensor is defective. Gene. weblink Phil.

The overlay part number is 316419103 If it happened while the oven was in cooking mode, start the troubleshooting from testing the temperature probe for continuity as described in the article Frigidaire Oven Error Codes The part number for the triple heating element is 316216703 Good luck." Ed // Apr 24, 2015 at 3:18 pm Hi Gene. Now the convection fan stays on and it throws a F30 error code.

the oven temperature sensor can be removed and tested for resistance and compared to the rtd scale in the image below.

Gene // Dec 24, 2014 at 1:10 pm Hello Craig, It is not difficult to do it but, for more accurate advice I need the complete model number of the oven. We'll see what happens when we replace the sensor.Cheers!T Expert: Mike replied6 years ago. darlene // Dec 19, 2014 at 7:03 pm The frigidaire stove my son has has a f10 code. F10 Error Code Kenmore Oven This error code means a shorted/faulty keypad.

I have seen many articles online about those connectors not being very good. Credentials confirmed by a Fortune 500 verification firm. The new one should solve it. check over here Parts cat.

Save model in your profile permanently Don't have a profile? Shorted Keypad. F4 or F31 - Shorted sensor (RTD probe) connection. Specifically the orange wire on the connector adjacent to the only non square or rectangular black component on the board.

Especially since the EOC had failed once before on warranty (it completely burned out and wouldn't work at all) and the repair tech told me that self clean was likely to Craig // Dec 24, 2014 at 6:30 am Hi Gene, Thanks for the information on this site. Check wiring in probe circuit for possible open condition. Also the model number you posted is incomplete.

Gene. If the reading is incorrect and the wires and plugs between the sensor and the EOC are good, replace the temperature sensor (RTD probe).