Home > Error Code > Hot Tub Error Codes

Hot Tub Error Codes


The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open In most cases, for newer spas anyway, the water flow problem can be quickly remedied and the spa will cool, reset and start again on it's own. About Me Kreg View my complete profile Aquarium PartsBath PartsPool PartsSpa PartsWhite GoodsClearance Items (Bath/Spa) Dealer/Tech ApplicationWarranty InformationProduct ReturnsBack Ordered ProductsDownloads SectionQuestions? Not sure what that is Thanks AnswerTommy, The FL code stands for FLOW which means that the spa does not sense enough water flow going through the heater and it usually

Contact your Dealer or Service Organization. If you have a Circ Pump, do this first (EL version):- Push the Jets 1 button once. Spa unusable. Back to Top OHS, OH, or SPA TEMP LMT Message There is an "Over Heated Spa" (OHS or OH) Water Condition.One of the Water Temp Sensors has detected 110°F (43.3°C) Incoming

Hot Tub Error Codes

SN = Non functional high temperature sensor. If you have no circulation this sounds like it. This code is used by the vendor to identify the error caused. Back to Top SAL or SANITIZER LOW Message At the ORP Sensor, the "Sanitizer Level is Low" (SAL).With an ORP Sensor Installed in the System, the Sanitizer Level is Below 740

Question about Dream Series Dream Master Hot Tub with Flex Cover 3 Answers What does FL mean on my hot tub?? tub?? They can be removed and cleaned, and should be each time you drain your spa. basic features: (repairs system freezing and rebooting issues , start-up customization , browser helper object management , program removal management , live updates , windows structure repair.) Recommended Solution Links: (1) Marquis Spa Error Codes FLO* = Flow Switch (heater is deactivated.

If not, you must open the access panel on the spa, and locate the correct pump. Balboa Hot Tub Error Codes This can be caused by a few different things. Viking supreme hot tub keeps tripping breaker. The temperature will rise only when the jets are turned on.

Back to Top - - F, - - C, or - - Message The Actual Water Temperature is "Unknown" (- -).Priming Mode has been Exited and the Pump has Not yet Hot Tub Error Code Oh If your water flow is perfectly fine, then you could have a problem with the thermostat or high limit switches used on older spa packs, which could fall out of calibration, The most common valve; the tee handle valve, will show that the handle is up, but in many cases the gate is still half closed, make sure that it is open First check the water level and make sure there is enough water going down the filter housing and it is not sucking any air.

Balboa Hot Tub Error Codes

If the error code goes away and you are getting the proper voltage then replace the pressure switch/flow switch. To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes. Hot Tub Error Codes Priming Mode lasts 4 minutes, but you can exit it earlier by pressing any Temp button. **Note: The term "circ pump" refers to a low-speed-only pump that is used for heating How To Fix Flo Error Hot Tub drops.

Heat Related Pump Not Running.8. this contact form Some panels need a prompt from you to restart. user-manual-Nitro... Heat Related Pump Not Running.8. Vita Spa Error Codes

This article contains information that shows you how to fix Fl Error Viking Spa both (manually) and (automatically) , In addition, this article will help you troubleshoot some common error messages Back to Top CFE or CONFIG ERROR Message There is a "Configuration Error" (CFE) in the Dip Switches or Configuration Settings.This Error Message indicates that the Dip Switch Numbers Displayed or Smartpool Nitro... Closed Slice Valve.7.

Back to Top PHH or PH IS HIGH LOWER PH Message At the pH Sensor, the "pH Level is High" (PHH).With a pH Sensor Installed in the System, the pH Level Great Lakes Hot Tub Error Codes If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1. Press "Mode" Button to Clear Message.

The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test.

This tool will scan and diagnose, then repairs, your PC with patent pending technology that fix your windows operating system registry structure. Test and Adjust pH Level per Manufacturers Instructions. To unlock all features and tools, a purchase is required. Hydropool Hot Tub Error Codes Back to Top LF or LOW FLOW Message There is a Verified "Low Flow" (LF) Condition in the Heater.The "HFL", "HL", or "HTR FLOW LOW" Fault has occurred 5 times in

Select "Message Other than CrC or CHKSUM FAIL" Below. The first thing you want to do before doing anything else is shut the spa down, remove the filter and make sure all the jets are open. Click here follow the steps to fix Fl Error Viking Spa and related errors. Monitoring the Sensors will Continue for 1 Hour.

Too Many Closed Jets.6.