laptopcomputerszone.com

Home > Error Code > Amana Ptac Error Codes

Amana Ptac Error Codes

Contents

CODE = C6 REFRIGERATION ALERT STATUS = Poor Unit Performance. CODE = EH Modes STATUS = Emeregency Hydronic Engaged. SnS = Sensors out of balance. Ecn = Spa operating in Economy Mode. http://laptopcomputerszone.com/error-code/hot-tub-error-codes.html

Check with dealer to determine proper capacity unit for application MOUNTING SUPPORT NOT INSTALLEDStorm window frame installed in windowSome models require removal of storm window frame before installation FROST ON INDOOR Please try the request again. Check the gas burner for proper installation and remove debris and dirt if you find any. So, make sure that the igniter generates sparks and that all the wiring connections are OK.

Amana Ptac Error Codes

Restore password × Upload manual upload from disk upload from url Thank you for your help! Spa has shut down. Has good flow.

SESH Sensor short, nonfunctional. Shut down Compressor and/or Heater, and energize high fan. Could indicate a flow problem. Sn2 = Nonfunctional temperature sensor.

error code should be inside heater make shure you have adequate gas pressure also sounds like bad flame sensor when flame sensor doesnt sense flame it will shut off after 7 Amana Ptac Error Code Eo If alternating with temp, may be temporary condition. OH = Over heat. http://www.spadepot.com/spa-error-codes.htm Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.

Clean the flame rod from scale build-up and burner from debris and dirt. SN = Non functional high temperature sensor. One sensor has detected 118º F at heater. Std Spa operating in Standard Mode.

Amana Ptac Error Code Eo

Check for clogged filter. i thought about this System will restart when temp. Amana Ptac Error Codes Water temperature has reached 118ºF. Otherwise, see Configuration Settings.

FC Freeze protection. http://laptopcomputerszone.com/error-code/amazon-s3-error-codes.html If water temperature drops 20ºF below set temperature, low speed pump and heater activates to bring temperature within 15º of set temperature. All rights reserved. Error Code 12 Problem: Rinnai error code 12 is usually associated with the flame failure.

If error codes are present they will be displayed. Leave unit running. Amana air conditioner error codes CODESTATUSDISPLAYERROR LIGHTSUGGESTED ACTION Models FPFreeze Protection Engaged. http://laptopcomputerszone.com/error-code/payflow-pro-error-codes.html Question about Rp2100 Pool & Spa Heater Lonox 407k Btu Natural Gas Polymer Header Digital Rp407aenc 1 Answer Heater fires and shuts off repeatedly.

Hold Panel sensors have been pressed too many times in a short period of time. OH Over heat. Spa has shut down.

ToE Time out error.

F2 Panel sensors have been pressed too many times in a short period of time. PnL Communication between the panel and circuit board is faulty. ---- Watchdog" (spa is deactivated) A problem has been detected. PSoL Pressure switch open with low pump. Could indicate a flow problem.

Power was lost or voltage is lowNNCheck for incoming power at correct voltage Airflow Alerts L6Discharge Air Too HotNYClean Filter or Remove Air Blockage LCOutdoor Coil Thermistor temperature highNYClean Condenser Coils, Browse Categories Answer Questions Raypak Pool and Spa Pump Pool & Spa Pumps All Unanswered Join Sign In Ask a Question × HomeForumTagserror code fpPool & Spa PumpsRaypak Share on Facebook ICE = Freeze protection. http://laptopcomputerszone.com/error-code/canon-fax-error-codes.html In some cases the unit may take action and shut the unit off until conditions are corrected.

It is exceedingly vital in lodgings with aged or sick occupants. Replace the sensor if needed. It will disable the operation until the temp get above 40Appl-Tech : CLICK HEREAppl-Tech : Nothing needs to be doneAppl-Tech : If you have additional questions feel free to continue this Spa Builders Spa Side Error Codes For more information regarding Spa Builders tech supportclick here Sn1 Nonfunctional high temperature sensor.

Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. Shut unit down for 5 minutes, Alternately flash error code and set point, then try again 2 times, if unit fails the 3rd time then shut unit down and alternately flash drops. PSoL = Pressure switch open with low pump.

BUT, you helped me figure out what part I needed for my hot tub and I really appreciated that:) I will highly recommend your website to anyone needing parts/and or service!!" PSoH Pressure switch open with high pump. Check gas solenoid valve for the short circuit. CODE = H1 FAILURES STATUS = High Voltage Protection engaged.

The LS switch is closed. DISPLAY = Y ERROR LIGHT = N SUGGESTED ACTION = Open load shedding switch to allow occupant unit operation. DISPLAY = Y ERROR LIGHT = N SUGGESTED ACTION = Open front desk switch to allow occupant unit operation. SEoP Sensor open or disconnected.

If condition repeats three times in one hour, shut unit down. It is spotless. Solution to these problems helps return any air conditioner to normal operation. Home Contact Amana PTAC R410A AC Error Codes August 10, 2014 Amana, Home CODE = FP Modes STATUS = Freeze Protection Engaged.

The EHH switch is closed. Check for proper spa water level and ensure pump is primed. Is there anything I can do to reset or do I need to call a tech? Share this conversation Expert: Appl-Tech replied3 years ago. Solution: Since your water heater was professionally installed and was working for some time, I will have the same assumption as with the above problem.